iPaint

COPPER PRO™ SCX™ Gallon - Multi-Season Boosted Ablative - 67% Copper, 2% SCX - Slime Control Xtra



The ratings are out for 2010, and let's state the ratings: Blue Water is now officially the Best Value AND the Highest Rated bottom paint tested independently by Practical Sailor, March, 2009. Check out the attached full article on the Bottom Paint Testing Challenge under FAQ link.

"Copper Pro SCX was the ONLY product rated "EXCELLENT" in the high copper ablative category at both test sites, and beat Interlux Micron Extra, Micron 66, Micron CSC, and beat Pettit Ultima Pro, Ultima SR, and beat Seahawk Biocop TF, Cukote, Cukote Biocide Plus & Islands 77, and West Marine PCA & CPP hands down." - March, 2009 - Practical Sailor.

COPPER PRO SCX 67 - SLIME CONTROL XTRA

ABLATIVE COPOLYMER ADVANCED TECHNOLOGY

MULTI-SEASON PROTECTION

Our best product - loaded with 67% copper, ablative with SCX - Slime Control Xtra. Rated "BEST BUY" - Compares to Interlux Ultra or Pettit Trinidad SR at a $40 savings!

Covers 300 - 400 square feet / gallon; 2 coats needed for proper application - 3rd coat recommended on the waterline

To figure out the amount of paint required: Length x Beam x .85 x 2 (2 coats)= Total / 300 feet = Gallonage Required

MULTI-SEASON PROTECTION - average boater (50 - 100 hours) will get anti-fouling protection of 2-3 years

* Self Polishing Boosted Ablative

* added SCX - SLIME CONTROL XTRA

* Multi Season Protection

* Relaunch Without Painting

* Eliminates Heavy Sanding

* Tremendous Protection for Extreme Fouling Conditions

Copper Pro SCX 67 provides extended antifouling protection against barnacles, algae and hydroids in salt and fresh water on boat bottoms only. SCX - SLIME CONTROL XTRA - acts like a sunscreen to prevent slime and algae. Its ablative copolymer base renders a smooth finish with durability and abrasion resistance. Copper Pro SCX 67 releases biocide by the constant exposure of new paint film to the water. Copper Pro SCX 67 has universal application over all types of properly prepared bottom paints (except aluminum). For use on fast fiberglass boats, as well as wood and steel hulls, extended protection is possible, since performance is directly proportional to the amount of paint applied.

Surface Preparation: Surface must always be clean, dry and properly prepared prior to painting. Failure to do so will lead to eventually blistering and/or peeling. All sanded surfaces must be wiped clean with 973 Dewaxer to remove sanding residue.

General Application: For use on boats below the true waterline. Can be brushed or rolled on fiberglass, wood, steel and previously painted surfaces per application systems below. Do not use on aluminum. Apply at least 2 coats for best performance, as the life of the paint is proportional to the number of coats applied. Mixing and Thinning: Shake or mix thoroughly and stir continuously while using. Thin when necessary with 974 Thinner.

Theoretical Coverage: Depending on surface conditions, one gallon of bottom paint will usually cover over 400 square feet of surface when brushed or rolled.

Clean Up: Use 974 Thinner for cleaning equipment and paint brushes.

Estimated Dry Times: Bottom paints are designed for overcoating after an overnight dry. Prior to launching, allow a minimum dry of overnight. If drying conditions are poor, or if paint was applied too thickly, longer periods of drying will be required. Fresh coats of paint must be thoroughly dry before overcoating.

Yearly Repainting: Scrub bottom clean at haul-out. Repaint only if old paint is sound and tight; if not, remove it by sanding or with paint remover. If old paint is rough, sand it with 100-150 grit sandpaper. Prepare seams, nicks and chips as below. Spotcoat any scuffs with antifoulant. Apply 2 coats of antifoulant.

On Bare Wood: If seams are not flush, fill them with seam compound. Dry several days until skin forms. Do not sand. Fill nicks with trowel cement, dry hard, sand, apply antifoulant (reduced 10%) then follow with 2 additional unreduced coats of antifoulant.

On Bare Fiberglass: Dewax by washing with 973 Dewaxer, remove dissolved wax at once with clean paper towels or rags; repeat; sand hard to a dull finish with 80-100 grit sandpaper. Fill any chips with trowel cement, dry hard, sand. Apply 5 coats of 8000A/8000B Bottom Protect High Build Epoxy Primer, then apply 2 coats of antifoulant.

On Bare Steel: Sandblast surface to a near white metal; remove blast residue with a broom and airhose. Wipe off with 973 Dewaxer. Do not sand. Fill in any imperfections with fairing compound. Sand smooth and wipe clean. Apply 5 coats of 8000A/8000B Bottom Protect High Build Epoxy Primer, then apply 2 coats of antifoulant.