Customer Service:


Coal Tar Epoxy 1 Gallon Kit

Item #8003K
AvailabilityUsually ships in 2-3 business days
Sale Price$74.95 - You Save 25%
Recommended Accessories
COPPER SHIELD - 45% Copper AblativeCOPPER SHIELD - 45% Copper Ablative $39.95
Mega Gloss Polyurethane EnamelMega Gloss Polyurethane Enamel $26.45
973 Dewaxer Quart973 Dewaxer Quart $9.45
974 Reducer/Thinner Quart974 Reducer/Thinner Quart $9.45
Hide Products
Using your mouse, click and "scratch" off the area below.
Product Description
Product Reviews
Product Video
Color Chart


• Heavy Duty High Build Epoxy Primer - 4:1 Mix

• Prevents Rust and Corrosion

• Excellent Adhesion & Abrasion Resistance

• Heavy Duty 4:1 Mix

• Recommended for Saltwater Immersion Service

• Conforms with U.S. Corp of Engineer - C-200 specification

• Perfect for Commercial Marine, Yacht & Industrial Use

Coal Tar Epoxy Primer is a heavy duty high build epoxy primer. Prevents rust and corrosion, has excellent adhesion & abrasion resistance, and Is recommended for saltwater immersion service. Conforms with U.S. Corp of Engineer - C-200 specification. • Perfect for commercial marine, yacht & industrial use.

SUGGESTED USES: Prevention of rust & corrosion



VEHICLE TYPE: Epoxy Resin, Polyamide Resin, Coal Tar Pitch


VOC: 175 grams / liter

SOLIDS BY VOLUME: 80% (reacted)

WEIGHT PER GALLON: 11 lbs. per gallon


COVERAGE: Theoretical coverage of 10 mils dry is 128 square feet per gallon. Material losses during mixing and application will vary and must be taken into consideration.

POT LIFE: 75 degrees F - 3-4 hours, lower at higher temperatures

AVERAGE DRY TIME 75°F: Dries to touch in 5-6 hours. Can recoat in 5 hours to 20 hours. Allow 5 hours minimum before recoating with antifouling.

RECOMMENDED REDUCER: Reduce with 974 Reducer as needed for proper flow and performance, 10% maximum.

RECOMMENDED CLEAN UP: 974 Reducer or Xylene

RECOMMENDED FINISH: Ablative or Epoxy Hard antifoulings

SURFACE PREPARATION: BARE FIBERGLASS: Degrease by wiping with a rag soaked in 973 Dewaxer. Sand with 80 grade (grit) paper. Remove sanding residue. Wipe with 973 Dewaxer.

Over Coal Tar Epoxy: Abrade surface by sweep blast or 36 grit sanding.

BARE METAL: Surface should be blasted to bright metal. Remove all blast or sanding residue using a clean air line and sweeping with a clean brush or broom. Vacuum clean for best results. Apply primer within 1 hour of metal preparation. If blasting is not possible (or if more than 2 hours has passed since blasting) sand or grind with coarse 36-60 grit discs. Remove sanding dust.

APPLICATION: Final Dry Thickness of 20 mils. This usually takes 2 coats, but the amount of paint is more important than the number of coats.

Airless Spray Pressure: 165 bar/2400 psi Tip Size: 0.44-0.53 mm/17-21 thou. Conventional Spray Pressure Pot: Pressure: 3.44-4.47 bar/50-65 psi (gun pressure); 10-15 psi (pot pressure). Tip Size: 1.5-1.8 mm/60-70 thou.

Brush Use a natural bristle brush.

Roller Use a 3/8” - 1/2” nap solvent resistant roller.

POT LIFE: 5 hours

LIMITATIONS: Do not apply if material, substrate or ambient temperature is below 50F or above 95F. Do not put over 1 part paints.

SHELF LIFE: Minimum 36 months

INDUCTION TIME: 20-30 minutes

MIXING: Mix 4 parts 8003 Part A Base and 1 part 8003 Part B Activator by volume at the specified ratio. Mix only as much as you can use in 2 hours. Mix small amounts until application technique is developed.

PACKAGE: 2 Part kit (1 (3/4 gallon fill) 8003A Base, 1 quart 8003B Activator)equals 1 full gallon mixed.

FREE SHIPPING for Orders over $200, FULLY BONDED, and 100% Guaranteed Return Policy (30 days).

User's Also Purchased