iPaint

Marine Alkyd Primer is a single component marine grade alkyd primer. Fast drying and good leveling characteristics. Good resistance to chemicals cleaners and abrasion.

Product description:

A one part alkyd primer Intended use:

Primer for MARINE ALKYD 50 finish. Use on steel, aluminum and wood. Product Info: Color White, Gray Finish / sheen Flat Curing agent Not applicable, one part only Volume solids 55±2% Mix ratio Not applicable, one part only Typical film thickness 2.0 – 3.0 mils DFT Theo coverage 588 square feet per gallon @ 1.5 mil DFT Flash point > 100 degree F Dry Times 40F 50F 75F 90F Touch dry 12 hr 8 hr 4 hr 3 hr Hard dry 36 hr 24 hr 10 hr 8 hr Overcoating 32 hr 26 hr 10 hr 8 hr Regulatory Data

VOC 340 grams /liter or 229 grams per kg

Systems and Compatibility:

MARINE ALKYD PRIMER must be applied over properly prepared surfaces. Surface Preparation: Major refurbishment: MARINE ALKYD PRIMER must only be applied over properly prepared surfaces. Surface must be clean, dry and free of contamination. MARINE ALKYD 50 must be applied within the overcoating intervals of the primer data sheet.

Maintenance and Repair: High pressure water wash using 3000 psi minimum to remove all contamination. Commercial Blast SSPC-SP6 (Sa 2) all bare steel or damaged areas. Repair any defect revealed after the blast. Do not allow surface to flash rust before application of MARINE ALKYD PRIMER, reblast as needed. Salt level must be below 10µg/cm˛ before painting. Surface must be clean, dry and free of contamination. Onboard Maintenance: Wash surface with fresh water to remove all contaminants. Remove all loosely adhered paint. Damaged areas should be prepared to Commercial Blast SSPC-SP6 (Sa2) or Power Tool Cleaning SSPC-SP3 (St 3). Prime bare steel surface with MARINE ALKYD PRIMER. Apply MARINE ALKYD 50 within the dry times specified by the primer data sheet.

Recoating: Within recoat times, wash surface to remove all contaminants and overcoat.

Application data:

Application: Apply by airless spray, brush or roll.

Mixing: One part paint, should be mixed thoroughly before application. Thinning: Not recommended. If thinning is necessary, add 5% of thinner by volume. Use THINNER 975 for exterior use only. Use THINNER 974 for interior use or brushing. Airless Spray: Airless spray is recommended. • Tip size is 13 - 19 thou. • Output fluid pressure at spray tip 2000 psi • Use water separator in line

Conventional Spray: Conventional spray is not recommended.

Brush: Brush use is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.

Roller: Roller use is recommended for small areas only. Multiple coats may be required to achieve specified film thickness. Use 1/4" medium nap roller cover.

Cleaner: THINNER 974 or 975. Cleanup: Flush all equipment with THINNER 974 or 975. Filter material prior to use. Flush spray equipment during heavy use. Dispose of paint cans in accordance with local regulations. Close lid thoroughly for storage.

Safety: Refer to Material Safety Data Sheet (MSDS) for this product. The MSDS will provide all necessary data on health hazards, conditions to avoid, proper storage, disposal information, hazardous ingredients and health related characteristics.

Limitations:

Performance of the product is dependant upon the specified film thickness being achieved. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Apply in good weather.Temperature of the surface to be coated must be at least 5°F above the dew point. Bring paint to 75°F prior to mixing and application. Store unused paint in a closed pail.Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures. As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating.

Unit size: • 5 US gallons in a 5 US gallon pail. • 1 US gallons in a 1 US gallon can.

Unit Weight: • 5 US gallons pail weighs 65 pounds • 1 US gallon can weighs 13 pounds

Shelf life: 12 months from the date of manufacture when stored in a protected location at 40-100°F

Office: Blue Water Marine 1999 Elizabeth Street, North Brunswick, NJ 08902, Phone 800-628-8422, Fax 732-821-8180, www.BlueWaterMarinePaint.com

Note: Data sheet information is not intended to be exhaustive. Use of this product for any purpose other than as specified without written confirmation from Blue Water does so at their own risk. Factors outside of Blue Water control may affect the performance of this product. Blue Water does not accept any liability for the performance of this product or any loss or damage caused by the use of this product. Information in this data sheet is subject to change. User is responsible for securing the most updated data sheet prior to use of this product. All product names mentioned in this data sheet are trademarked by Blue Water Marine.