iPaint

POOL SHIELD CRX CHLORINATED RUBBER XTRA

VOC COMPLIANT - AVAILABLE FOR PURCHASE ALL IN ALL STATES

FOR CONCRETE POOLS ONLY - NOT FOR FIBERGLASS OR SPAS

• Concrete & Plaster

• Resists Chlorine & U.V. Rays

• Silicone & UV Stabilizers act like a “Sunblock”

• Ease of Application

• Excellent Color Retention

• Cures Quickly

• Non-Fading

• Excellent Recoatability

RATED #1 by over 10 magazines, including Pool & Spa Life, Luxury Pool Design, Outdoor Living Features, AG Custom Pool Magazines.



Our top selling Chlorinated Rubber pool paint, Chlorinated Rubber Xtra! Pool Shield CRX is our exciting extended life chlorinated rubber pool paint. Built on decades of experience, Long life performance provides extended life. Silicone and UV stabilizers act like a "sunblock" which slows the effect of harmful UV rays. Crammed full of high solids chlorinated rubber gives extended waterproof protection. Refresh that tired pool today with the standard in the industry, and enjoy your pool for years to come!

300 - 400 square feet / gallon; 2 coats needed for proper application - No Primer Needed - Self Priming Paint

To figure out the amount of paint required: Length x Width x 1.7 = square footage x 2 (2 coats) / 300 square feet = gallons needed

Proper Surface Preparation is important - Wash down with TSP solution (TSP powder into a 5 gallon bucket with water)using a scrub brush. Then take 1 gallon of muriatic acid & put into a 5 gallon bucket - fill with 4 gallons of water. Scrub down the pool with this acid solution. Then rinse with the TSP solution, and let the pool dry. Then paint with 1 coat, overnight dry, 2nd coat, wait 5 days to refill. Add 1 extra day for every day of rain. Enjoy!



POOL SHIELD CRX™ - Chlorinated Rubber XTRA

A PREMIUM Type A chlorinated rubber coating designed for maximum protection against UV rays and chlorine for new or old concrete pools. Fortified with UV Additives and Silicone which acts like a “Sunblock” for maximum protection against blistering UV sunrays. Apply over other chlorinated rubber pool paints in good condition, as well as bare concrete and plaster surfaces. Dries quickly, durable, and resists fading, chemicals and abrasion. Designed for maximum protection against algae, UV rays, automatic pool cleaning machines and chlorine.

SUGGESTED USES: Concrete, plaster pools. Not for use on spas and whirlpools.

COLORS: Available in 6401 White, 6402 Medium Blue, 6403 Aqua, 6404 Royal Blue, 6405 Sky Blue, 6406 Black.

FINISH: Gloss. For a non-skid finish, add pumice stone, sand or marbledust to paint as needed to achieve desired appearance.

VEHICLE TYPE: Chlorinated Rubber

SOLVENT TYPE: High Flash Naphtha, Mineral Spirits

FLASH POINT: 83°F Seta Flash

SOLIDS BY WEIGHT: 60%

WEIGHT PER GALLON: 11 lbs. per gallon (varies by color)

RECOMMENDED DRY FILM: 4.0 mils

COVERAGE: Theoretical coverage at two mils dry is 400 square feet per gallon, and recommended thickness of 4 mils dry would require 2 full coats. Material losses during mixing and application will vary and must be taken into consideration. Expect 50% less coverage on bare, rough or sandblasted surfaces.

VISCOSITY AT 75°F (24°C): 70-80 KU

AVERAGE DRY TIME 75°F: Dries to touch in 1 hour. Lower temperatures & higher humidity will slow down dry times. Can re-coat in 24 hours. Allow 5 days for complete cure before filling pool with water. Add 1 day for every day of rain.

RECOMMENDED REDUCER: 70023 Solvent Reducer, High Flash Naphtha or Xylene as needed for proper rollout performance.

RESISTANCE TO: Chlorine, Alkali, Algae, Mineral Oils, Fresh and Salt Water

RECOMMENDED PRIMERS: Self Priming

APPLICATION: Brush, Spray or Roller (preferred) Roll: 3/8” nap mohair metal, lambskin, phenolic core roller. Keep roller wet. Roll in one direction, rewet, then cross roll.

Spray: Conventional Air 50 -70 psi, Tip Size .055 -.070,

Airless 2200-2500 psi, Tip Size .019-.023.

SURFACE PREPARATION: Water blast the surface to remove all loose paint, dirt, oils and grease. Clean with a Tri-Sodium Phosphate (TSP) wash, scrubbing surface to get rid of oil, dirt and suntan lotions, and then etched with a 15-20% solution of muriatic acid. Then thoroughly rinse with TSP & flush with plenty of fresh water and allowed to dry thoroughly. Glossy surfaces should be power sanded to a 80 grit profile for proper adhesion. WAIT 5 DAYS AFTER FINAL COAT BEFORE FILLING POOL WITH WATER.

POT LIFE: Not Applicable

LIMITATIONS: Do not apply if material, substrate or ambient temperature is below 50°F or above 95°F. NOT FOR VINYL LINED OR METAL POOLS.

SHELF LIFE: Minimum 12 months

MIXING: Mechanically mix well for 10 minutes, apply as it comes from the container, and thin with 70023 Solvent Reducer, High Flash Naphtha or Xylene as needed for proper performance.

PACKAGE: 1 Gallon cans (2 per case), 5 Gallon pails