COVID-19 UPDATE:
Due to COVID-19 we are currently closed. We apologize that we are not able to accept any new orders at this time. Thank you for your patience and understanding.
$33.03 $41.28
SAFETY INFORMATION REQUEST FORM FAQ
$99.18 $123.97
SAFETY INFORMATION REQUEST FORM FAQ
$66.10 $82.63
A PREMIUM one-part industrial enamel that are designed for all applications of steel, wood and masonry. Formulated especially as a heavy duty protective and decorative coating to withstand severe exposures. An epoxy resin, rust inhibitive paint for new or previously painted structural steel, rolled steel, aluminum all types of wood and masonry surfaces. Special processed chemical ingredients protect metal and wood against rust, rotting, corrosion, mildew and chipping and fading. The result is a finish that provides outstanding appearance over the exposure cycle.
*** Not Recommended for floors with Autos or Forklifts. The preferred product for that application is Epoxy Kote - 2-part epoxy. ***
SUGGESTED USES: Exterior, interior, concrete, steel, equipment, and anywhere a rugged industrial coating is needed
LIMITATIONS: Do not apply if material, substrate or ambient temperature is below 50°F or above 95°F.
COLORS: Available in over 30 factory packaged colors, as well as 1000 mixed colors.
FINISH: Gloss
VEHICLE TYPE: Epoxy Resin
SOLVENT TYPE: High Flash Naphtha VOC: 3.76 lbs. / gal (450 grams / liter)
SOLIDS BY WEIGHT: 50%<
WEIGHT PER GALLON: 10 lbs. per gallon (varies by color)
RECOMMENDED DRY FILM: 4.0 mils
COVERAGE: Theoretical coverage at two mils dry is 400 square feet per gallon, and recommended thickness of 4 mils dry would require 2 full coats. Material losses during mixing and application will vary and must be taken into consideration. Expect 50% less coverage on bare, rough or sandblasted surfaces.
VISCOSITY AT 75°F (24°C): 70-80 KU
AVERAGE DRY TIME 75°F: Dries to touch in 4 hours. Lower temperatures & higher humidity will slow down dry times.
RECOMMENDED REDUCER: Xylene for spray application, Hi Flash Naphtha for brushing or rolling
RESISTANCE TO: Chemical Resistance, Abrasion, Oils, Grease, Rust, Corrosion, Mildew, Chipping and Fading
RECOMMENDED PRIMERS: Jetcote Industrial Primers - 3038 Gray, 3037 Red, 3036 Black, 3039 Yellow
APPLICATION: Brush, Spray or Roller Roll: 1/2” nap mohair metal, lambskin, phenolic core roller. Keep roller wet. Roll in one direction, rewet, then cross roll. Product can be reduced as needed with Hi Flash Naphtha to allow proper flow out and performance.
Spray: Conventional Air Gravity Feed 59-70 psi, Tip Size .055 -.070, Airless 2200-2500 psi, Tip Size .013-.017. Product can be reduced with Xylene as needed for proper flow out and performance. For Air Spray reduce 25% with enamel reducer (Xylene.).
SURFACE PREPARATION: Water blast surface to remove all loose paint, dirt, oils and grease. Abrade with 240 grit dry sandpaper or equivalent. Solvent wipe down to remove all sanding residue. Prime with Jetcote Primer for best results.
POT LIFE: Not Applicable
SHELF LIFE: Maximum 12 months MIXING: Mechanically mix for 10 minutes, making sure that all solid material is mixed thoroughly.
PACKAGE: 1 Gallon cans, 5 gallon pails.
CLEANUP: Xylene for Equipment.
$14.80 $18.50
SAFETY INFORMATION REQUEST FORM FAQ
$19.75 $24.69
Zip-guard Metal Finish will provide long lasting protection on all types of surfaces, including metal, wood, masonry, and plastic. Zip-guardʼs proprietary ZIPRUST Technology™ encapsulates rusty surfaces without the need for specialty primers. Designed for exterior and interior applications, Zip-guard will resist the damaging effects of severe weather and provide long lasting corrosion and chemical resistance, without the need for specialty primers.
RECOMMENDED USES: Zip-guard Rust Preventive Urethane Metal Finish is designed to provide beautiful protection to most types of metal surfaces including railings, fences, doors, furniture, whether clean or rusted, as well as on wood and concrete surfaces. Not for floors.
SURFACE PREPARATION: Zip-guard Rust Preventive Urethane Metal Finish will adhere well to all properly prepared surfaces. Any loose material, such as rust, or paint must be removed by scraping, sanding or wire-brushing. All dirt, oil, grease, mildew, salt, which can contaminate the surface must be cleaned. Product will adhere well to most metal surfaces ( ie. Copper, bronze, stainless steel, galvanized metal and aluminum) as long as surface is cleaned prior to application. If washing is necessary, use a non-soapy detergent such as tri-sodium phosphate (TSP) and/or a commercial mildew remover. Rinse the surface thoroughly and let dry completely before continuing. The shine on glossy surfaces must be removed by sanding.
APPLICATION: Eye protection is recommended. Recommended application temperature is between 60°F and 80°F. Mix thoroughly before and during application. Always maintain a wet edge, but avoid over-brushing and/or rolling finish in one direction. Corners, edges and heavily pitted areas are must be adequately coated. Apply one or more coats as needed. If second coat is needed, allow overnight dry cure. Full cure and hardness is achieved after 7 days. One heavy coat is all that is needed on most surfaces. On vertical applications we recommend two thin coats.
APPLICATION METHOD: Brush, Roller or Spray. Airless Spray: Use .017-.021 tip size at approximately 1800-2600 psi.
Conventional Spray: Use .007-.008 tip size, pot pressure 15-20 psi and atomizing pressure 25-35 psi.
NO THINNING REQUIRED: If thinning is necessary, use Zip-guard Metal Finish Thinner.
COVERAGE: Approximately 250 square feet per gallon depending on the method of application, porosity and texture of the surface.
CLEAN-UP/DISPOSAL: Clean all tools and equipment after use with Zip-guard Metal Finish Thinner. If spilled, contain spilled materials and remove with inert absorbent. Dispose of contaminated absorbent container and unused contents in accordance with local, state and federal regulations.
EMAIL REQUEST FOR SAFETY INFORMATION
View full product details