Durashield Industrial Polyurethane Enamel - Gallon
Free Gift

Size
Shine*

  • FREE SHIPPING A PREMIUM one-part industrial enamel that are designed for all applications of steel, wood and masonry. Formulated especially as a heavy duty protective and decorative coating to withstand severe exposures. An alkyd-based, rust inhibitive paint for new or previously painted structural steel, rolled steel, aluminum all types of wood and masonry surfaces. Special processed chemical ingredients protect metal and wood against rust, rotting, corrosion, mildew and chipping and fading. The result is a finish that provides outstanding appearance over the exposure cycle.

     

    SAFETY INFORMATION REQUEST FORM FAQ
    1. STEEL, WOOD, MASONRY
    2. RUST INHIBITIVE
    3. MILDEW PROOF
    4. EASE OF APPLICATION
    5. EXCELLENT COLOR RETENTION
    6. NON FADING
    7. EXCELLENT RECOATABILITY
    8. HIGH HIDING
    9. LONG LASTING
    1. SUGGESTED USES: Exterior, interior, concrete, steel, equipment, and anywhere a rugged industrial coating is needed
    2. LIMITATIONS: Do not apply if material, substrate or ambient temperature is below 50°F or above 95°F.
    3. COLORS: Available in over 30 factory
    4. packaged colors, as well as 1000 mixed colors.
  • FINISH: Gloss
  • VEHICLE TYPE: Alkyd Resin
  • SOLVENT TYPE: High Flash Naphtha
  • VOC: 3.76 lbs. / gal (450 grams / liter)
  • SOLIDS BY WEIGHT: 50%
  • WEIGHT PER GALLON: 10 lbs. per gallon (varies by color)
  • RECOMMENDED DRY FILM: 4.0 mils
  • COVERAGE: Theoretical coverage at two mils dry is 400 square feet per gallon, and recommended thickness of 4 mils dry would require 2 full coats. Material losses during mixing and application will vary and must be taken into consideration. Expect 50% less coverage on bare, rough or sandblasted surfaces.
  • VISCOSITY AT 75°F (24°C): 70-80 KU
  • AVERAGE DRY TIME 75°F: Dries to touch in 4 hours. Lower temperatures & higher humidity will slow down dry times.
  • RECOMMENDED REDUCER: Xylene for spray application, Hi Flash Naphtha for brushing or rolling
  • RESISTANCE TO: Chemical Resistance, Abrasion, Oils, Grease, Rust, Corrosion, Mildew, Chipping and Fading
  • RECOMMENDED PRIMERS: Jetcote Industrial Primers - 3038 Gray, 3037 Red, 3036 Black, 3039 Yellow
  • APPLICATION: Brush, Spray or Roller
    Roll: 1/2” nap mohair metal, lambskin, phenolic core roller. Keep roller wet. Roll in one direction, rewet, then cross roll. Product can be reduced as needed with Hi Flash Naphtha to allow proper flow out and performance.
    Spray: Conventional Air Gravity Feed 59-70 psi, Tip Size .055 -.070, Airless 2200-2500 psi, Tip Size .013-.017. Product can be reduced with Xylene as needed for proper flow out and performance. For Air Spray reduce 25% with enamel reducer (Xylene.).
  • SURFACE PREPARATION: Water blast surface to remove all loose paint, dirt, oils and grease. Abrade with 240 grit dry sandpaper or equivalent. Solvent wipe down to remove all sanding residue. Prime with Jetcote Primer for best results.
  • POT LIFE: Not Applicable
  • SHELF LIFE: Minimum 12 months
  • MIXING: Mechanically mix for 10 minutes, making sure that all solid material is mixed thoroughly.
  • PACKAGE: 1 Gallon cans, 1 quart cans, 5 gallon pails.
  • CLEANUP: Xylene for Equipment.

Related Items

Back to the top