Back to the top

Epoxy Kote Heavy Duty Concrete Epoxy Paint - 2 Gallon Kit

Epoxy Kote Heavy Duty Concrete Epoxy Paint - 2 Gallon Kit

Size
Shine*
  • FREE SHIPPING A PREMIUM two-part solvent based epoxy coating designed for maximum protection, ease of application, outstanding gloss and color retention, chemical resistance and adhesion over a variety of substrates. Longest lasting protection against fade. Apply over most types of epoxy coatings in good condition, as well as bare concrete and steel. Dries quickly, durable, and resists fading, chemicals and abrasion. Mix ratio is 1:1.

     

    SAFETY INFORMATION REQUEST FORM FAQ
    1. Covers 500 - 600 square feet per 2 gallon kit per coat; 2 coats recommended for proper application
    2. Epoxy Kote™ is our PREMIUM two-part solvent based epoxy coating designed for maximum protection, ease of application, outstanding gloss and color retention, chemical resistance and adhesion over a variety of substrates.
    3. Longest lasting protection against fade.
    4. Apply over most types of epoxy coatings in good condition, as well as bare concrete and steel.
    5. Dries quickly, durable and resists fading, chemicals and abrasion. Mix ratio is 1:1.
    1. SUGGESTED USES: Interior, concrete floors, steel, equipment, and anywhere a rugged industrial coating is needed
    2. LIMITATIONS: Not recommended for applications requiring extended exterior exposure. Do not apply if material, substrate or ambient temperature is below 50°F or above 95°F.
    3. COLORS: Available in over 100 factory packaged colors
    4. FINISH: Gloss
    5. VEHICLE TYPE: Epoxy Resin & Polyamide Curing Agents
    6. SOLVENT TYPE: Xylene, Diacetone Alcohol, Butyl Cellosolve
    7. VOC: 3.5 lbs. / gal (420 grams / liter)
    8. SOLIDS BY WEIGHT: 58%
    9. WEIGHT PER GALLON: 10 lbs. per gallon (varies by color)
    10. RECOMMENDED DRY FILM: 4.0 mils
    11. COVERAGE: Theoretical coverage at two mils dry is 400 square feet per gallon, and recommended thickness of 4 mils dry would require 2 full coats. Material losses during mixing and application will vary and must be taken into consideration. Expect 50% less coverage on bare, rough or sandblasted surfaces.
    12. VISCOSITY AT 75°F (24°C): 70-80 KU
    13. AVERAGE DRY TIME 75°F: Dries to touch in 2 hours. Lower temperatures & higher humidity will slow down dry times. Recoat with no sanding required between 16 hours and 72 hours.
    14. RECOMMENDED REDUCER: Xylene for spray application, High Flash Naphtha for brushing or rolling
    15. RESISTANCE TO: Chemical Resistance, Abrasion, Oils, Grease
    16. RECOMMENDED PRIMERS: Procote™ U/E 824N 2-Part Epoxy Gray Primer
    17. APPLICATION: Brush, Spray or Roller
      Roll: 3/8” nap mohair metal, lambskin, phenolic core roller. Keep roller wet. Roll in one direction, rewet, then cross roll. Product can be reduced as needed with High Flash Naphtha to allow proper flow out and performance.
    18. Spray: Conventional Air Gravity Feed 59–70 psi, Tip Size .055 –.070, Airless 2200-2500 psi, Tip Size .013-.017. Product can be reduced with Xylene as needed for proper flow out and performance. For Air Spray reduce 25% with urethane reducer (Xylene.).
    19. SURFACE PREPARATION: Water blast surface to remove all loose paint, dirt, oils and grease. Abrade with 240 grit dry sandpaper or equivalent. Solvent wipe down to remove all sanding residue. Prime with Epoxy Kote™ U/E 824N 2-Part Epoxy Gray Primer for best results.
    20. POT LIFE: 6 hours at 75°F, 50% Humidity.
    21. SHELF LIFE: Minimum 12 months
    22. MIXING: Mechanically mix for 10 minutes both Part A & Part B individually, and then mechanically mix 10 minutes the combined volumes (1:1 Mix Ratio). Allow mixed solution to induct for 30 minutes before using. Mix only what you expect to use in an 6 hour period.
    23. PACKAGE: 1 Gallon cans, 5 gallon pails.
    24. CLEANUP: Xylene for Equipment.