Back to the top

Jetcote™ - Industrial Primer Gallon

Jetcote™ - Industrial Primer Gallon

Size
Shine
Color*
3035 White Oxide Primer
3036 Black Oxide Primer
3037 Red Oxide Primer
3038 Gray Oxide Primer
3039 Yellow Oxide Primer
  • FREE SHIPPING A PREMIUM one-part industrial primer that are designed for all applications of steel, wood and masonry. Formulated especially as a heavy duty protective and decorative primer to withstand severe exposures. An alkyd-based, rust inhibitive primer for new or previously painted structural steel, rolled steel, aluminum all types of wood and masonry surfaces. Special processed chemical ingredients protect metal and wood against rust, rotting, corrosion, mildew and chipping and fading. The result is a primer that provides outstanding appearance over the exposure cycle.

     

    SAFETY INFORMATION REQUEST FORM FAQ
    1. STEEL, WOOD, MASONRY
    2. RUST INHIBITIVE
    3. MILDEW PROOF
    4. EASE OF APPLICATION
    5. EXCELLENT COLOR RETENTION
    6. NON FADING
    7. EXCELLENT RECOATABILITY
    8. HIGH HIDING
    9. LONG LASTING
    1. SUGGESTED USES: Exterior, interior, concrete, steel, equipment, and anywhere a rugged industrial coating is needed.
    2. LIMITATIONS: Do not apply if material, substrate or ambient temperature is below 50°F or above 95°F.
    3. COLORS: Available in 3035 White, 3036 Black, 3037 Red, 3038 Gray, and 3039 Yellow.
    4. FINISH: Flat
    5. VEHICLE TYPE: Alkyd Resin
    6. SOLVENT TYPE: High Flash Naphtha
    7. VOC: 3.76 lbs. / gal (450 grams / liter)
    8. SOLIDS BY WEIGHT: 50%
    9. WEIGHT PER GALLON: 10 lbs. per gallon (varies by color)
    10. RECOMMENDED DRY FILM: 4.0 mils
    11. COVERAGE: Theoretical coverage at two mils dry is 400 square feet per gallon, and recommended thickness of 4 mils dry would require 2 full coats. Material losses during mixing and application will vary and must be taken into consideration. Expect 50% less coverage on bare, rough or sandblasted surfaces.
    12. VISCOSITY AT 75°F (24°C): 70-80 KU
    13. AVERAGE DRY TIME 75°F: Dries to touch in 30 minutes. Can speed up dry time by adding Xylene. However, this will change the VOC rating. Check local laws for compliance.
    14. RECOMMENDED REDUCER: Xylene for spray application, Hi Flash Naphtha for brushing or rolling.
    15. RESISTANCE TO: Chemical Resistance, Abrasion, Oils, Grease, Rust, Corrosion, Mildew, Chipping and Fading
    16. RECOMMENDED FINISH: Durashield Industrial Enamel - 3000 Series
    17. APPLICATION: Brush, Spray or Roller Roll: 1/2” nap mohair metal, lambskin, phenolic core roller. Keep roller wet. Roll in one direction, rewet, then cross roll. Product can be reduced as needed with Hi Flash Naphtha to allow proper flow out and performance.
      Spray: Conventional Air Gravity Feed 59-70 psi, Tip Size .055 -.070, Airless 2200-2500 psi, Tip Size .013-.017. Product can be reduced with Xylene as needed for proper flow out and performance. For Air Spray reduce 25% with enamel reducer (Xylene.).
    18. SURFACE PREPARATION: Water blast surface to remove all loose paint, dirt, oils and grease. Abrade with 240 grit dry sandpaper or equivalent. Solvent wipe down to remove all sanding residue. Prime with Jetcote Primer for best results.
    19. POT LIFE: Not Applicable
    20. SHELF LIFE: Minimum 12 months
    21. MIXING: Mechanically mix for 10 minutes, making sure that all solid material is mixed thoroughly.
    22. PACKAGE: 1 Gallon cans, 5 gallon pails.
    23. CLEANUP: Xylene or High Flash Naphtha for Equipment.