Speedy Dry™ Acrylic Primer - Gallon
Free Gift


    1. Heavy Duty Acrylic Coating
    2. 5 Year Warranty
    3. Over 100 Colors Available in Stock
    4. Acrylic Hardener Improves Gloss & Chemical Resistance
    5. Concrete and Metal Surfaces
    6. High Solids Formulation Equals More Coverage
    7. Reduces Maintenance Costs
    8. Rustproof Finish
    9. Chemical Resistant
    10. Superb Adhesion


  • A PREMIUM one-part acrylic coating designed for maximum protection, ease of application, outstanding gloss and color retention, chemical resistance and adhesion over a variety of substrates. Longest lasting protection against fade. Apply over most types of epoxy coatings in good condition, as well as bare concrete and steel. Dries quickly, durable, and resists fading, chemicals and abrasion. Mix ratio is 1:1.
    1. SUGGESTED USES: Interior, exterior concrete floors, steel, equipment, and anywhere a rugged industrial coating is needed
    2. LIMITATIONS: Do not apply if material, substrate or ambient temperature is below 50°F or above 95°F.
    3. COLORS: Available in over 100 factory packaged colors
    4. FINISH: Gloss
    5. VEHICLE TYPE: Acrylic Resin
    6. SOLVENT TYPE: Xylene, Hi Flash Naphtha
    7. VOC: Maximum of 3.5 lbs. / gal (420 grams / liter)
    8. SOLIDS BY WEIGHT: 58%
    9. WEIGHT PER GALLON: 10 lbs. per gallon (varies by color)
    10. RECOMMENDED DRY FILM: 4.0 mils
    11. COVERAGE: Theoretical coverage at two mils dry is 400 square feet per gallon, and recommended thickness of 4 mils dry would require 2 full coats. Material losses during mixing and application will vary and must be taken into consideration. Expect 50% less coverage on bare, rough or sandblasted surfaces.
    12. VISCOSITY AT 75°F (24°C): 70-80 KU
    13. AVERAGE DRY TIME 75°F: Dries to touch in 2 hours. Lower temperatures & higher humidity will slow down dry times. Recoat with no sanding required between 16 hours and 72 hours.
    14. RECOMMENDED REDUCER: Xylene for spray application, High Flash Naphtha for brushing or rolling.
    15. RESISTANCE TO: Chemical Resistance, Abrasion, Oils, Grease
    16. RECOMMENDED PRIMERS: Procote™ U/E 824N 2-Part Epoxy Gray Primer
    17. APPLICATION: Brush, Spray or Roller
      Roll: 3/8” nap mohair metal, lambskin, phenolic core roller. Keep roller wet. Roll in one direction, rewet, then cross roll. Product can be reduced as needed with High Flash Naphtha to allow proper flow out and performance.
      Spray: Conventional Air Gravity Feed 59–70 psi, Tip Size .055 –.070, Airless 2200-2500 psi, Tip Size .013-.017. Product can be reduced with Xylene as needed for proper flow out and performance. For Air Spray reduce 25% with urethane reducer (Xylene.).
    18. SURFACE PREPARATION: Water blast surface to remove all loose paint, dirt, oils and grease. Abrade with 240 grit dry sandpaper or equivalent. Solvent wipe down to remove all sanding residue. Prime with Procote™ U/E 824N 2-Part Epoxy Gray Primer for best results.
    19. HARDENER:Mix 1 pint of Acrylic Hardener (optional) to 1 gallon of Acrylic Enamel
    20. SHELF LIFE: Minimum 12 months
    21. MIXING: Mix can mechanically for 10 minutes, then add 1 pint of Acrylic Hardener (optional) for 5 minutes.
    22. PACKAGE: 1 Gallon cans, 5 gallon pails.
    23. CLEANUP: Xylene for Equipment.

Related Items

Back to the top